P3 elecraft in Title/Summary

Elecraft PX3 Utility

Elecraft PX3 Utility is used to send firmware to your Elecraft PX3 Panadapter. This free utility may also be used to send commands described in the PX3 Programmer's Reference to your PX3. Your PX3 must be connected to a personal computer serial COM port before firmware can be sent.

• Publisher: Elecraft, Inc.
• Last updated: July 7th, 2016

Elecraft K3 Utility

The Elecraft K3 Utility helps you update, configure, calibrate, and use your K3. The Port tab is used to identify the computer serial port used to communicate with your K3 . The Firmware tab is used to load K3 firmware . The Configuration tab is used to Save K3 configuration settings to a file on your personal computer.

• Publisher: Elecraft Inc.
• Last updated: November 29th, 2015

Elecraft K144XV Utility

With an Elecraft K144XV internal 2 meter module installed, your K3 will make another leap forward in versatility. The K144XV covers the full 144-148 MHz U.S. allocation, so you can do weak-signal CW/SSB work as well as access 2-m repeaters in your area.

• Publisher: Elecraft, Inc.
• Last updated: February 1st, 2012

P3 elecraft in Description

K-Keys

This program allows the operator to call CQ and give contest exchanges with the CW and RTTY memory keyer built into the Elecraft K3 and with the optional Elecraft KDVR3 voice keyer (if installed in your radio), and can also access numerous additional functions including band and mode changes, select filter bandwidths, even tune the radio.

• Publisher: K-Keys (KE3C)
• Last updated: February 10th, 2012

Elecraft KXPA Utility

The Elecraft KXPA Utility is used to send firmware to your KXPA100 Amplifier and may be used for diagnosis and control. Connect the KXPA100's upper RS-232 connector to a serial port on your personal computer using a standard serial cable or a USB to Serial Adapter such as the Elecraft KUSB.

• Publisher: Elecraft, Inc.
• Last updated: January 26th, 2016

K2Net

K2Net was intended to allow remote operation of an Elecraft K2 across a network. The main objective was to allow control and operation across a home local area network,so that you can use the radio anywhere in the house, or out in the garden, via a Wi-Fi connected laptop.

• Publisher: Julian Moss
• Last updated: October 27th, 2011

Elecraft XG3 Utility

Elecraft XG3 Utility is a program designed for XG3 RF Signal Source device. A break signal is now transmitted over the serial port at the start of frequency sweep and Morse memory playback. This appears as a 1.3 ms low to high to low pulse on the serial TX line and can be used to trigger external equipment.

• Publisher: Elecraft, Inc.
• Last updated: January 21st, 2014

ARRL November Sweepstakes Contest Log

ARRL November Sweepstakes Contest Log is a contest logging software tool designed for the ARRL November Sweepstakes event. The program checks for duplicates, lists all contacts, displays a map of sections, provides many current statistics, provides DX spotting, interfaces with most Elecraft, Icom, Kenwood and Yaesu radios, writes Cabrillo file format for log submission, and more.

• Publisher: N3FJP Software - Affirmatech, Inc
• Home page: www.n3fjp.com
• Last updated: August 18th, 2017

Additional P3 elecraft selection

Elecraft P3 Utility

This P3 Utility version can be used to load P3 Firmware versions 0.27 and above to your P3. The K3 TX frequency is now indicated by a red cursor whenever RIT, XIT and/or SPLIT are selected on the K3. Use this software to load the latest firmware into your P3.

• Publisher: Elecraft, Inc.
• Last updated: March 1st, 2015

Elecraft KPA Utility

KPA Utility is used to send firmware to your KPA500 Linear Amplifier. Features: -fixed 6m SWR calculation problem with low reflected power; -the Fault speaker is now disabled at shutdown; -ALC threshold control now has much better resolution, using its entire range.

• Publisher: Elecraft, Inc.
• Last updated: October 24th, 2011

Elecraft Frequency Memory Editor

The Elecraft Frequency Memory Editor helps you maintain frequency memories using a spreadsheet format. Memories can be recalled using K3, K3S, and KX3’s M>V switch or the memory editor’s “QSY” buttons. Once memories are stored in your K3, K3S, and KX3, you can disconnect the K3, K3S, and KX3 from the PC.

• Publisher: Elecraft
• Last updated: January 31st, 2017

CQ WPX Contest Log

CQ WPX Contest Log is an easy-to-use general logging program. The program features: lists prefix multipliers, lists all contacts, displays the continent worked, beam heading and distance from your QTH, many current statistics, interfaces with most Elecraft, Icom, Kenwood and Yaesu radios, DX spotting, and more.

• Publisher: N3FJP Software - Affirmatech
• Home page: www.n3fjp.com
• Last updated: November 20th, 2015

CQ WW DX Contest Log

This is a worldwide contest logging application for Windows. It has an intuitive interface which lists all your contacts. The country multipliers are listed by band. It displays the continent worked, beam heading and distance from your QTH. CQ WW DX Contest Log can also be interfaced with most Elecraft, Icom, Kenwood, and Yaesu radios.

• Publisher: N3FJP Software - Affirmatech
• Home page: www.n3fjp.com
• Last updated: September 7th, 2015

KComm

KComm is meant to be an easy to use low resource usage log keeping program for the average K2 or K3 operator who may be a casual DXer or contest participant. Rather than try to do everything itself, KComm interfaces with some of the best available software for data mode operation and morse decoding so that you can use one logging program for all modes.

• Publisher: Julian, G4ILO
• Last updated: December 2nd, 2010

VHF Contest Log

VHF Contest Log logging application for various contests such as ARRL January VHF Sweepstakes, ARRL June VHF QSO Party, ARRL September VHF QSO Party, CQ World Wide VHF, etc. This program interfaces with most Elecraft, Icom, Kenwood and Yaesu radios. It provides various statistics, DX spotting, contact info, etc.

• Publisher: N3FJP Software - Affirmatech, Inc.
• Home page: www.n3fjp.com
• Last updated: February 23rd, 2016

ARRL 10 Meter Contest Log

ARRL 10 Meter Contest Log amateur radio software tool. The program checks for duplicates (including partials), lists all contacts, lists multipliers by mode, provides a country look-up function, writes Cabrillo file format for log submission, provides many current statistics, interfaces with most Elecraft, Icom, Kenwood and Yaesu radios, provides DX spotting, and more.

• Publisher: N3FJP Software - Affirmatech
• Last updated: January 31st, 2016

IS K2 remote

K2 Remote is a basic demonstration RS-232 control program designed for the K2 that runs under Windows (95,98, 2000, XP & ME). It requires the K2 KIO2 RS-232 control option to operate and is provided free without warranty for your use with our KIO2 option.

• Publisher: Elecraft
• Last updated: October 7th, 2011

KRC2 Config

If you have the jumper for W5 installed in your KCR2 then select the "W5 Jumper In" option. Having this jumper installed allows you to use all seven XV settings in the K2 to control an output, so you will see horizontal rows XVTR1 - XVTR7 (as shown above). If it is removed, then select the "Out" option and only XVTR1 - XVTR3 will be available for band mapping.

• Publisher: Elecraft LLC