Parallel port programming pci in Title/Summary

Parallel Port PIC Programmer

Parallel Port PIC Programmer uses PC's parallel port for communication between the programming software and simple PIC programmer hardware. OshonSoft.com Parallel Port PIC Programmer software is very easy to use and works on all Windows platforms. Simulator IDE should also be installed on your PC prior to using this programming software.

• Publisher: Oshon Software
• Last updated: April 1st, 2008

Lalim Parallel Port Control

Most of engineering industry using PC to control hardware with using additional I/O card but with Lalim Parallel Port Control you can use your default printer port controlling external device such as switching on/off light or control electronic devices. What does this program [does is] trigger the parallel port (Printer port) 's data pin by your command.

• Publisher: Lalim Software
• Last updated: September 12th, 2008

Lalim Parallel Port Control Professional

Lalim Parallel Port Control can control hardware through the parallel port (printer port) and can also control a remote PC parallel port through a network. Lalim Parallel Port Control requires a certain knowledge of electronics and if you are not comfortable with a soldering iron, or don't know what a 1k resistor is, then it is probably advisable that you do not attempt to use this program.

• Publisher: Lalim Software
• Last updated: December 6th, 2008

Parallel port programming pci in Description

GE-Flash

GE-Flash is a complete X2212/X2444 programming system for programming Phoenix, Delta and Ranger radios on Windows 2000 and Windows XP. A simple parallel port adapter and kernel mode driver allows direct programming of X2212 and X2444 EPROM's on your PC.

• Publisher: rtzaudio
• Last updated: July 17th, 2018

BASCOM-AVR

BASCOM AVR is a very powerful and easy-to-use compiler for the AVR series of micro controllers developed by Atmel. The program comes with a very user-friendly interface and a set of simple commands, and provides more flexibility than other programs in this category.

• Publisher: MCS Electronics
• Home page: www.mcselec.com
• Last updated: December 15th, 2016

LabTool-48UXP

LabTool-48UXP is an intelligent universal programmer. Main features: - USB or parallel port interface with auto-switch power - Support 5V and 3.3V low voltage devices, 1.8V chip support through low voltage adapter. - Less then 2 seconds per Mbit Programming speed for high density flash chip. - No adapter required for DIL chip up to 48-pin.

• Publisher: Advantech Equipment Corp.
• Last updated: April 19th, 2013

SoftCollection Parallel Port Viewer

SoftCollection Parallel Port Viewer lets you view and change the state of selected Parallel Port. You can select the required LPT port from its menu. Using the displayed pin-outs of parallel port, you can connect your electronic circuit without any error. Please remember to use a resistor of at lest 500 ohm to protect your computer.

• Publisher: SoftCollection
• Home page: www.soft-collection.com
• Last updated: November 26th, 2015

BasicX

The BasicX Programming Environment uses the PC parallel port for the BX01 Chip and the BasicX Emulator. Windows 95/98/ME can access the port automatically. The Test program is pre-loaded on the SPI EEPROM chip at the factory. It will work until another program gets downloaded to the chip.

• Publisher: NetMedia, Inc.
• Last updated: April 19th, 2008

Additional Parallel port programming pci selection

PonyProg2000

Ponyprog is very powerful and popular microchip programmer. Ponyprog enables the user to program EEPROM, FLASH and PIC's using user friendly tools and multiple programmer types. Ponyprog supports AVR, SPI eeprom, AVR micro, 12C bus 8bit eeprom, PIC 16 micro, PIC 12 micro, AT89S micro and SDE2506 eeprom family chips.

• Publisher: Claudio Lanconelli
• Last updated: August 2nd, 2017

Parallel Port Control

A simple User Control developed in C#.Net used to control the Parallel Port. The following tasks can be performed using it: - Send data to Data Pins. - Receive data from Data Pins. - Send data to Control Pins. - Receive data from Control Pins. - Read current status of Status Pins. - Implement Synchronous and Asynchronous Loops. - Implement UP, DOWN and UP-DOWN Counters.

• Publisher: Jaspreet Kaleka
• Home page: jaspreetscodezone.blogspot.ro
• Last updated: October 2nd, 2010

Timer

This is a program that enables the PC to connect to the outside world, by using the printer and parallel port LPT1. Hardware can then be connected to the computer to control solenoids, relays, lights and sensors etc. Timer, consists of 11 forms. A main form, 8 output forms, 1 inputs form and a settings form. The main form gives the status of all 8 outputs and 5 inputs.

• Publisher: Hot Time Software
• Last updated: October 13th, 2011

KELLYWARE KCam

KCam Router/Mill software is designed to run low cost hobby CNC equipment. Program your paths using the built in Gcode editor, or import DXF, NC, and PLT files. Create signs and plates using your CAD software and import your work into KCam. Dual cutting depth allows for holes and outlines to be punched out after routing.

• Publisher: KellyWare
• Home page: www.kellyware.com
• Last updated: April 12th, 2012

Printfil

Print from DOS, Unix, Linux to Windows printers: USB, GDI, PDF, e-mail, network, IP, fax. Capture LPT1:-LPT9: & COM1:-COM9: and redirect the jobs, even to a printer physically connected to the captured port and w/out physical LPT/COM ports installed

• Publisher: aSwIt Srl: Mail, Print for DOS, Windows
• Home page: www.printfil.com
• Last updated: December 18th, 2022

Z-Downloader Utility

Z-Downloader Utility is a free program that can be used to send firmware and files to printers, over network, USB, RS-232 or Parallel port connections. The program automatically detects the printers connected to your computer and displays the information.

• Publisher: Zebra Technologies
• Last updated: April 29th, 2015

Notebook Manager

Notebook Manager is a management software that allows you to control various hardware and software settings on your personal laptop computer. The Notebook Manager contains 9 functions which allows you to view and/or config your laptop computer's BIOS settings and Microsoft Windows functions.

• Publisher: Acer
• Last updated: July 25th, 2008

DriveGLEAM

DriveGLEAM is a harddrive activity indicator and also include built in extensions for monitoring CPU and memory load. It works by immitating the harddrive LED on screen. This is a very useful if your computer case is hidden (under the table) or on another physical location (remote desktop).

• Publisher: Svein Engelsgjerd
• Last updated: December 22nd, 2011

DSLR Shutter

DSLR Shutter is designed to be a simple tool to capture long-exposure images from digital SLR cameras using their "bulb" setting. It allows you to specify the number of frames, their duration, and various delays to act as a software interval timer for your camera.

• Publisher: Stark Labs
• Last updated: March 19th, 2011

LcdStudio

LcdStudio the premiere Lcd Software supporting Lcd with the Sed133x, T6963c ,LC7981 or ks0108 controllers connected to the parallel port at any display panel size, giving the end user access to easy to use graphical componentes such as labels, gauges, clocks and even animated images.

• Publisher: LcdStudio
• Last updated: January 16th, 2012